Inventory of Oilfield Process Equipment

Vessel/Separator - 16" x 7'6' S/S 1440 psi - Vertical c/w 100 BBL Tank Sweet Service - NRG 565

Information
Ask a Question

Vessel/Separator - 16" x 7'6' S/S 1440 psi - Vertical c/w 100 BBL Tank Sweet Service - NRG 565

1.0 VESSEL
 16” OD x 7’- 6” S/S x 1440 PSI MAWP VERTICAL SEPARATOR
Constructed with Alberta, BC and Sask Registration
Built in 2006
100°F Design Temperature
RT-4, No PWHT
M.D.M.T.-20F @ 1440 Psig
Designed 3 Phase, Dressed 3 Phase

VESSEL CONNECTIONS:
N1 Inlet (1) - 3” NPS CL600 RF
N2 Gas Outlet (1) - 3” NPS CL600 RF
C3 Condensate Outlet (1) - 2” NPS CL3000 TOL
C4 Water Outlet (1) - 2” NPS CL3000 TOL
C5 Condensate LC (1) - 2” NPS CL3000 TOL
C6 Water LC (1) - 2” NPS CL3000 TOL
C7 PSV (1) - 2” NPS CL3000 TOL
C8 HLSD (1) - 2” NPS CL3000 TOL
C9 a/b Condensate LG (2) - ¾” NPS CL3000 TOL
C10 a/b Water LG (2) - ¾” NPS CL3000 TOL
C11 PI (1) - ½” NPS CL3000 TOL
C12 TI (1) - ¾” NPS CL3000 TOL
C13 Drain (1) - 2 NPS NPT

2.0 TANK
100BBL DOUBLE WALL TANK
Built in 2006
9’-6” Diameter x 8’ High
3/16” Thk Walls and Roof, ¼” Thk Floor
Built to 12F Spec
Rectangular Manway, Ladder, Thief hatch, Gauge Board
Insulated with spray foam insulation
3” NPT Load Out
3” NPT HLSD
2” NPT Inlet

4.0 SKID AND BUILDING SPECIFICATION

SKID BASE, 8’- 0” W X 22’- 6” L
Main Skid Members – W8 x 18#/ft
Cross Members – W6 x 15#/ft
Floor Supports – C4 x 5.4#/ft
3/16” Checker Plate under building only
Roll Ends

FOAM PANEL BUILDING
8’-0” Wide x 6’-0” Long (Estimated) x 8’-4” Low Eave Height
Shed Style Roof
1 ½” Galvalume Foam Panel R-12 Insulation Rating
One (1) 3’-0” x 7’-0” Foam Panel Door c/w, IWG Window, Check Chain, Panic-
Hardware, and Weather-Stripping
One (1) 36” x 36” Double Glazed Sliding Window c/w Screen
Two (2) 12” x 12” Adjustable Louvers c/w Screen
H-211 1 CATADYNE 24” x 24” MK BUILDING HEATERS
Sweet Natural Gas
12 VDC Starting Element with 30’ Cables
C/w Grill, Vent Hood, Safety Shutoff, 912 Regulator, Maxitrol Regulator and
Thermostat

5.0 FUEL GAS SYSTEM

V-100 1 4” OD X 30” OAL 285 PSI MAWP FUEL GAS SCRUBBER
Mechanical HLSD (Reduces Outlet to 1" NPT)
1/16” Corrosion Allowance
-20/650°F Design Temperature
Registered in Alberta, BC, Sask. & Manitoba.
PRV-200 1 FISHER 627 PRESSURE REGULATOR
1" NPT, Body Material: WCC Steel
Spring Case Material: Aluminium
1/8" Orifice Aluminium Nylon Disk
Spring Range 70‐150 Psig
Maximum Inlet Pressure: 2000 Psig
PSV-100 1 TAYLOR PRESSURE RELIEF VALVE
Model 8200
1” NPT Inlet x 1” NPT Outlet
Sweet Service Trim, WCB Body
“D” Orifice, 150 Psig Set Pressure
PRV-200 4 FISHER 67CFR INSTRUMENT REGULATOR
1/4” FNPT Connections
Sweet Service Trim
250 Psig MAWP
Three (3) 0 to 35 Psig Spring Range

7.0 PACKAGING SPECIFICATIONS

-Relief valves piped outside
-Piping to skid edge c/w individual connections
-Package is readied or dismantled only to the extent required for shipping
-All piping, instrument tubing and equipment will be adequately supported
-All flange and open ends of piping will be covered for shipment
-All instruments to be vented off skid individually
- Fuel gas is supplied by process gas downstream of the meter run, w/ ½” tubing to fuel gas regulator
- Inlet piping is 2” CL600 at skid edge, with removable spool for 2” ESD valve, increases to 3” at vessel
- Condensate piping is 1” NPT, with turbine meter, bypass and prover taps and recombines with gas leg
- Water piping is 1” NPT, combines with vessel drain and is directed to 100BBL tank.

8.0 NOTES

- Package was built in 2006 and is not believed to have been put in service
- No original QC information is available on existing package.
Shop UT of the Vessel
Function Test of Instruments
Recertification of the PSVs
Paint Touch-up as necessary
Any Rebuilds or Repairs required are additional
No Spooling quoted downstream of meter runs. Small spool from Meter Runs to floor support.
P&ID and Bill of materials included.
Full general layout as built drawings will be an additional cost.

Additional information

Job Number

NRG 565

Size

16" x 7' 6"

Pressure

1440 psi

Orientation

Vertical

Service

Sweet

A#

A554154

CRN

AB, BC, Sask, R4871.213

U #

YES

Year Built

2006

Manufacturer

Hanover

Location

Ponoka

Have questions about Vessel/Separator - 16" x 7'6' S/S 1440 psi - Vertical c/w 100 BBL Tank Sweet Service - NRG 565?

Start your next project with
NRG Process Solutions

Cape Manufacturing
Blue Diamon Design Corporation
WestCan Fabrication Ltd

Oilfield Process Equipment Solutions

SiteBuilderOne | Privacy Policy | Sitemap  
©2022 NRG Process Solutions, All rights reserved.

NRG Process Solutions phone-handsetcross-circle